How We Choose and Make Our Lock Picks
Every Dangerfield pick starts life as high-yield, Starship-grade 301 stainless. We polish it slowly for 48 hours and prove each design on a bench of real locks before it earns a place in a set. Here's what that steel does in your hand, and why we chose it.
Stainless steel lock picks: is 301 too soft?
Only before it's worked. Raw 301 is soft. Cold-rolled to a high-yield temper, it's one of the stiffest, springiest steels a pick can be cut from, and it's the steel in every Dangerfield pick.
You may have heard that 301 stainless is a bit softer than other steels. That's true of 301 straight from the mill. The chart shows the published data on what cold rolling does to it, and further down you can see what that means for the pick in your hand.
High-yield 301 takes nearly nine times the load of raw 301 before it bends for good
Yield strength is how much stress steel can take and still spring back straight. Higher is better for a pick.
Steel figures from Elvencraft's "Lock Pick Metallurgy", which compiles supplier data and treats it as a rough guide. The annealed figure is the ASTM A666 minimum. Sources are listed at the foot of the page.
Raw 301 and worked 301 are two different animals
301 is an austenitic stainless steel, and it gets nearly all of its strength from being rolled cold. Straight from the mill, annealed, it's soft enough to bend by hand. Every pass through the rollers squeezes its crystals flatter and locks more strain into them, so the steel gets stiffer and springier each time.
Full-hard 301 has had a good dose of rolling and suits stamped, budget tools. High-yield 301 is worked harder again, and it's the temper we cut Dangerfield picks from. Elvencraft puts high-yield 301 at about 51 on the Rockwell C hardness scale, against about 41 for full-hard 301.
Heat undoes all of that work and drops the steel back to its soft annealed state, which is why high-yield 301 has to be cut and finished cold.
Illustration of the grain structure, simplified. Yield figures are the published values from the chart above.
Where a pick takes the load
Push on the tip of a pick and the steel has to carry that force all the way back to your fingers. The further you get from the tip, the longer the lever, so the stress builds along the shaft. On our short hook it peaks at the base of the shaft, 10.9 mm (0.43 in) before the steel widens into the handle, because that's where the lever is long and the steel is still narrow. Once the handle widens, it carries the load easily.
Bending stretches one face of the steel and squeezes the other. Push the tip down and the top face goes into tension while the bottom face goes into compression, with no stress at all along the middle. If the stress anywhere passes the steel's yield strength, that spot takes a permanent bend and the pick no longer runs true.
We've modelled a push across the flat of the pick, which is its easiest direction to bend. Cut from high-yield 301, our short hook takes about 700 g (24.7 oz) at the tip before it bends for good. The same pick in annealed 301 would take a set at about 80 g (2.8 oz).
Calculated from published yield values and our pick's measured dimensions, simple beam model. The pick is the Praxis short hook, 0.584 mm (.023 inch) thick and 2.37 mm (0.093 in) wide at the peak, which sits 35.3 mm (1.39 in) back from the hook. Bending stress is 6 × force × lever ÷ (width × thickness²).
Illustrative drawing. It shows how the two kinds of steel behave at a thin tip, with no measured values.
Hard isn't the same as good
If hardness were the whole story, pick makers would reach for the hardest tool steel they could find. They don't, because very hard steel is brittle. Load a thin hook tip made from it and it chips, cracks or snaps off inside the lock.
A lock pick has to flex a touch under tension, spring back true after every lift, and carry each pin's movement straight to your fingertips. That takes spring-back and toughness together, and it's exactly what high-yield 301 gives you.
Made by people who pick
Every Dangerfield design starts as a prototype on our own bench. We test it on a workbench of UK, European, US and world locks, from paracentric keyways to security pins and from worn old cylinders to brand-new ones, and the people doing the testing have been picking for decades.
Once a design earns its place, we make it in small craft batches in our own warehouse.
In the photo: our Learn Lock Picking Kit, with a Serenity pick working the repinnable practice lock and the Beginners Visual Guide open beside it.
Steel names and steel grades
Some brands give their steel a special-sounding name. We'd rather tell you the grade: Starship-grade 301 stainless, the grade SpaceX first chose for Starship.
A grade can be checked
301 is a published standard grade. Its minimum properties are set out in ASTM A666 and printed on every steel supplier's datasheet, so anyone can look up what it is.
A name tells you nothing
A made-up steel name points to nothing you can look up. If a pick maker won't tell you the grade, it's fair to ask why.
Good company
Many of the most respected pick makers cut from 301 too. We tell you the temper as well, and ours is high-yield.
Is a titanium lock pick set better?
Titanium picks are a clever marketing story. Titanium sounds exotic and looks great in a product photo, but in the hand it tells you less. Titanium alloys are about half as stiff as steel: Elvencraft lists their Young's modulus at 16 million psi, against 30 million psi for steel.
A softer pick bends where a steel pick would push, and that give swallows the small pin movements you're trying to feel. To make up for it, titanium picks get cut thicker, and thick picks struggle in the tight keyways of better locks. You'd be paying more for a pick that feels mushier, so we'll stay with steel.
Our picks, cut from high-yield 301
We make Dangerfield picks in small craft batches in our own warehouse. Every design is tested on a workbench of real locks before it goes into a set.
A 48-hour slow polish
Each pick is polished slowly for 48 hours until the tip is glass-smooth, so it glides past the pins and lets you feel every set.
Full tang
The steel runs the full length of the pick in one piece, with no weld or glued joint to work loose.
Hand-checked
Every pick is checked by hand before it's finished, so the one in your set is straight and true.
Questions about pick steel
Isn't 301 stainless steel a bit soft for lock picks?
Only before it's worked. Raw 301 is soft, which is exactly why it's chosen: cold-rolled and spring-tempered, it turns into one of the stiffest, springiest steels you can make a pick from. That's what we cut Dangerfield picks from. A lock pick doesn't need to be as hard as possible, because very hard steel chips and snaps at a thin tip. It needs to spring back true after every lift and carry each pin's movement straight to your fingertips. That's why many of the most respected pick makers use 301 too. Some brands give their steel a special-sounding name. We'd rather tell you the grade: Starship-grade 301 stainless, the grade SpaceX first chose for Starship.
Will stainless steel lock picks rust?
301 is a stainless grade, so it shrugs off sweaty hands and damp pockets. Carbon spring steel can start to rust within days of contact with sweat, which is one reason we don't use it. Give your picks a quick wipe after a session and the polish stays bright.
Which thickness should I pick with first?
Praxis comes in two thicknesses, 0.58 mm and 0.38 mm (0.023 and 0.015 inch), and each handle is etched with its inch gauge so you can tell them apart. The 0.023 picks feel solid and carry plenty of feedback in standard keyways. Reach for the 0.015 picks when a keyway is tight or the warding is narrow.
Sources
- Elvencraft, "Lock Pick Metallurgy", table of yield strength and ultimate tensile strength: 301 high-yield cold-rolled 260 ksi (1,790 MPa) yield; 1095 carbon steel tempered at 400°F 152 ksi (1,048 MPa); 301 and 302 full-hard cold-rolled 140 ksi (965 MPa); 301 and 302 annealed 30 ksi (205 MPa). Same page for Rockwell C hardness of about 51 (high-yield 301) and about 41 (full-hard 301), Young's modulus of 16 million psi for titanium alloys and 30 million psi for steel, and carbon spring steel rusting. elvencraft.com/lpd/Lock Pick Metallurgy.html
- United Performance Metals, Type 301 stainless datasheet, minimum room-temperature properties per ASTM A240 and A666: annealed yield strength 30 ksi (205 MPa). upmet.com 301 datasheet (PDF)
- ASTM A666, Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. store.astm.org/a0666-10.html
- Load section: our own calculation. The pick outline is the measured drawing of the Praxis short hook (.023 inch), and the bending stress uses the simple cantilever formula with the yield values in source 1. It is a model, not a lab test.


